Nissan Pulsar N14 Workshop Manuals and Repair Manuals

To check the brake fluid level in your Nissan Pulsar N14, locate the brake fluid reservoir, typically located near the firewall in the engine compartment. Remove the cap and visually inspect the fluid level, making sure it is within the "MIN" and "MAX" marks on the reservoir. If necessary, add the recommended brake fluid specified in your automotive repair manual to bring the level up to the appropriate mark.

To change the spark plugs in your Nissan Pulsar N14, locate the spark plug wires or ignition coil packs in the engine compartment. Carefully disconnect the wires or coil packs from the spark plugs, one at a time, using a twisting motion. Use a spark plug socket and ratchet to remove the old spark plug, then install the new one, tightening it to the specified torque mentioned in your automotive repair manual. Finally, reconnect the wires or coil packs to the spark plugs.

To check the transmission fluid level in your Nissan Pulsar N14, start the engine and let it idle for a few minutes to warm up. Locate the transmission dipstick, usually labeled and located near the engine. Pull out the dipstick, wipe it clean, reinsert it fully, then pull it out again to check the fluid level. The level should be within the "HOT" range on the dipstick. If necessary, add the recommended transmission fluid specified in your automotive repair manual.

To perform a basic engine tune-up on your Nissan Pulsar N14, start by replacing the spark plugs, inspecting and replacing the distributor cap and rotor if necessary, checking and adjusting the ignition timing, inspecting and replacing the air filter, and inspecting and replacing the fuel filter. Additionally, you may want to clean the throttle body and idle air control valve for optimal performance. Consult your automotive repair manual for detailed instructions on each step of the tune-up process.

To replace a blown fuse in your Nissan Pulsar N14, locate the fuse box, usually found in the engine compartment or under the dashboard. Open the fuse box and refer to the diagram on the inside cover or in the automotive repair manual to identify the fuse corresponding to the malfunctioning component. Use a fuse puller or a pair of needle-nose pliers to remove the blown fuse and replace it with a new one of the same amperage rating.

To replace a broken side mirror in your Nissan Pulsar N14, start by removing the interior door panel to gain access to the mirror mounting bolts or screws. Disconnect the electrical connector if applicable, then remove the bolts or screws securing the mirror assembly. Carefully detach the broken mirror and replace it with a new one, aligning the mounting holes. Reinstall the mirror assembly, tighten the bolts or screws, and reconnect the electrical connector.

To replace a faulty headlight bulb in your Nissan Pulsar N14, open the hood and locate the backside of the headlight assembly. Disconnect the electrical connector from the bulb and remove the bulb retaining clip or cover. Carefully remove the old bulb and replace it with a new one, making sure not to touch the glass part with your fingers. Reinstall the retaining clip or cover and reconnect the electrical connector.

To replace the air filter in your Nissan Pulsar N14, locate the air filter housing, usually located in the engine compartment, and remove the clips or screws securing it. Open the housing and carefully take out the old air filter, making note of its orientation. Insert the new air filter, ensuring it is properly seated, and reattach the housing and secure it using the clips or screws.

To reset the maintenance light in your Nissan Pulsar N14, turn the ignition switch to the "ON" position without starting the engine. Within ten seconds, fully depress the accelerator pedal three times, then release it. The maintenance light should start flashing, indicating that it has been reset. If the light does not go off or continues to flash, it is recommended to refer to your automotive repair manual for further troubleshooting.

It is recommended to change the oil in your Nissan Pulsar N14 every 5,000 to 7,500 miles or every six months, whichever comes first. Regular oil changes help maintain engine performance and prolong the life of your vehicle. Refer to your automotive repair manual for specific instructions on the type of oil to use and the proper oil change procedure.

The recommended interval for replacing the timing belt in a Nissan Pulsar N14 is typically around 60,000 to 90,000 miles or every 5 to 7 years, whichever comes first. It is crucial to replace the timing belt at the specified interval to prevent engine damage and avoid potential breakdowns. Consult your automotive repair manual for more precise information on the timing belt replacement procedure and recommended mileage.

The recommended tire pressure for a Nissan Pulsar N14 is typically 32 PSI (pounds per square inch) for all four tires. However, it is advisable to refer to the specific guidelines mentioned in your automotive repair manual as tire pressure can vary depending on the load, driving conditions, and tire size.

If your Nissan Pulsar N14's battery is dead, you can jump-start the vehicle using jumper cables and another vehicle with a charged battery. Connect the positive terminal of the dead battery to the positive terminal of the charged battery, then connect the negative terminal of the charged battery to a metal surface on the dead vehicle. Start the engine of the charged vehicle and let it run for a few minutes, then try starting your Nissan Pulsar N14.

The type of coolant recommended for your Nissan Pulsar N14 is typically a mixture of ethylene glycol-based antifreeze and distilled water in a 50:50 ratio. It is important to use the coolant specified in your automotive repair manual to ensure proper engine cooling and prevent corrosion. Refer to the manual for specific instructions on checking and topping up the coolant level as well.